79064091301 Kenmore Range - Instructions

Watched the video

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair company wanted $370. I did it in 45 min. for less than $100.

my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great

It was a replace racks not repair. No problem

Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.

The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. Pull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.

Removed the back panel, disconnected the terminals and removed the old one and installed the new one.

Simple Just plugged it in !

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

I couldn't explain how to do the job any better than your instructional video does. As long as you follow the video instructions you should have no problems.

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.