Models > 36272224202 > Instructions

36272224202 Kenmore Range - Instructions

Jump to:

All Instructions for the 36272224202
46 - 60 of 92
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
LEAH from YUMA, AZ
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAPHNE from CHICAGO, IL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PHILL from SOMERSET, NJ
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
the tubes both leaked
replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from BOSCOBEL, WI
Parts Used:
WB20K8
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Getting thew the back
I put it in the same way tuck it out
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
NEIL from ROCKY POINT, NY
Parts Used:
WB08T10026
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana from LEEDS, AL
Parts Used:
WB01K10112
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from LEAGUE CITY, TX
Parts Used:
40A15
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Change bulb
Easy
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from The Villages, FL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marie from Woodstock, IL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juanita from GAINESVILLE, GA
Parts Used:
WB16K10070, WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roscoe G from ROCHESTER, NY
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kaylinda from Berwick, ME
Parts Used:
WB07K10118, WB07K10117
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Caterers melted the plastic part on our stove
Unbolted the old parts, cleaned the stove, and bolted the new parts on. Looks just like brand new!! The parts were perfect, easy to find, inexpensive, and delivered quickly!
Thank you!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
eric from reno, NV
Parts Used:
WB07K10118, WB07K10117
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken plastic end caps
repair was easy,couldn't believe I found parts. Bought house with stove in it.wife wanted new one,replaced broken parts cleaned up oven saved 600 bucks.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Geneseo, NY
Parts Used:
WB20K8
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Monterey, TN
Parts Used:
WB08T10026
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 36272224202
46 - 60 of 92