79091106890 Kenmore Range - Instructions

Just use flat screwdriver to press on clip and just squeeze it in

After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

replaced it

I just had to plug the new burner plate in the receptical
and it works again very well.

The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Removed drawer and replaced broken and missing parts. Very easy when you have correct parts.

Took the new parts out of the bags, slipped them into place and had the drawer working flawlessly in less than 5 minutes!
I surprised myself.

They snap right into place in the holes at the front of the stove and the drawer is then slid back onto the glides and works properly once again.

I removed the brokne ones and replaced them with the new ones.
I appreciated PartSelect giving a picture of the parts so i didn't have to search for the part number.

Ge wanted over a hundred dollars for the same part you charged only $80. Thanks. I'll be buying again.