9117388810 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- AMANDA from Boston, MA
- Parts Used:
- WB2X9154
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Oven Igniter had burnt out
Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what they're doing will do it much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Delran, NJ
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not light
Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Monticello, MN
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven wouldn't heat
I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The new igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Clare, MI
- Parts Used:
- WB2X9154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not light
It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Bayside, NY
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven broiler worked but oven would not ignite
Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Fords, NJ
- Parts Used:
- WB14X103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Hinge
Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Reseda, CA
- Parts Used:
- WB20X107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defective spark module
used nut driver to remove old module and 10 minutes the cooktop was back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brethren, MI
- Parts Used:
- WB2X9154
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not light - no glow igniter
Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.
Could not get at the screws holding the igniter to the buner, without removing the burner.
Could not get at the screws holding the igniter to the buner, without removing the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Elkridge, MD
- Parts Used:
- WB2X9154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven igniter would not heat so gas valve would not open
removed the old part with socket set and replaced the part with a fresh one. turned on oven, igniter heated up and oven lit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Glenview, IL
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door hinge
The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OLABODE from MATTESON, IL
- Parts Used:
- WB2X9154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The oven igniter was not functioning.
Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Skokie, IL
- Parts Used:
- WB2X9154
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
oven wont heat
I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.
Was this instruction helpful to you?
Thank you for voting!