3627181192 Kenmore Range - Instructions

replaced lights in refrigirator and freezer

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

slid the old ones out and slid the new ones in. done

This oven is from 1993 and a lot less complicated than today's models probably are. The first things to do are to remove the oven door and broiler pan. On this model, the oven door simply lifts off the hinges. Once these are gone, you want to remove the oven floor. To remove, locate the two screws at the back of the floor. After removing, lift the floor up and towards the back to pull the floor tongue out of the groove in the front. This will expose the gas jet and ignitor assembly. At the front of the jet pipe is a screw that holds the pipe to the front center of the frame - it is underneath so you may have to bend over to see it, it can be felt easily as well. Remove this screw, this will allow the pipe to be moved a little later. In front of the assembly is a vertical metal plate with a screw at the right of the mounting the plate into the broiler floor. Remove the screw and slide the plate to the left to pull out another tongue/groove set-up. Now you should see the wires completely and the connection to the air-flow adjuster. There is a small screw in the front of this brass fitting, it does not need to be touched. Turn the burner pipe clockwise while lifting and this should pop the assembly up. The ignitor is mounted to the burner pipe by 2 screws that are found on the bottom of the mount. Remove the 2 screws, this will allow the ignitor to hang free. Be sure to pay attention to what wire attaches to what wire, I marked the left wire so that I knew which to reconnect to after the change over. Remove the caps on the wires if this unit has been removed before, if not then mark the wires on both the replacement unit and the original wires. My ignitor has been replaced before, so I used my wire cutter to clean-up the ends of the old connection before reconnecting the new replacement. At this point, you should be able to fire-up the oven, it might take a moment for the new one to warm up, so give about 30-40 seconds. If the oven fires up, it's then working to put everything into place in reverse order. I like to line up the parts and pieces as I remove so I can just put back in reverse.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom plate of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

Stuck the dial/knob onto the existing stem for oven temp. control. Not exactly rocket science. It was harder to find the part than to install it.

removed two rear screws, pulled out range bottom, dropped new one in place, and reinstalled screws...VIOLA! works like a charm. I'm a woman and 53 years old ...If I can do it... you can too!

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Since I'm not very mechanical I had my service manager from work come to my house and fiqure out the problem. By using an electrical meter he found that there was no continuity in the igniter. So being the mechanical guy I am I watched him take out 2 screws that secured the the piece of metal that covers the bottom part of the stove. He pulled that part out and from there it was 2 screws to release it from the back of the stove and 2 more to disconnect the igniter from the burner tube. We ordered the part and it arrived in 3 days. I opened the box and to my dismay it was broke. I called to tell them that it was broke and they ordered me a new one right then. I had that part the next day very grateful for that. I was able then to put it back together myself and it worked. Wife is extremely happy with me.

Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.

Very was ti replace racks and knobs. Very fast mail service

Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.