91193218990 Kenmore Range - Instructions

I had read some of the other comments about the repairs. The one that I found most useful was the one describing how short the connector was once they are removed. That isn't a joke about 3/4". My sujestion is to have tape and tape them to the back of the oven so as to not to loose them in the insulation. Once that was removed and reconnected the oven worked again like new. Even the most novice of people will find it a breeze.

unplugged stove-removed cover in back of stove-unplugged element-inside oven removed two screws-removed element. reverse procedure to install. took about twenty minutes.
wife happy again.
parts came in two days. I could not believe how fast it came. Thank You very much! Jim Jewkes

Being that the rest of the stove was functioning fine, it was still plugged into the electrical outlet, after unplugging the range, I used a nutdriver and and removed the back panel exposing the two electrical clips on the old heating element. After unplugging the two electrical clips, I removed the two screws that secure the heating element to the back of the inside of the range. Once the screws were removed, the heating element came right out. I inserted the new element, installed the two screws previously removed, plugged the two electrical clips on the back of the heating element, re installed the back panel, plugged the range in and cooked lasagna. Total repair time was 12 minutes.

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

I'm so pleased with the ease of placing my order, the price, and the speed of delivery. My only challenge was figuring out the correct part to order, as I didn't have an owner's manual for the range when we moved into the house. But once I located the model # in the range's lower drawer, the website did a good job of guiding me toward the correct replacement part. In my case there was no "repair" involved; I was simply replacing a broken lower oven rack. I would definitely use this company again.

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

1ST..Cut power at circuit breaker.
2ND..Using nut driver, remove two sheet metal nuts.
3RD..Gently tilt element upward and pull out until wire connectors show. There are two wires with flat connectors, use the vise grips to hold the wires so they don't slip back behind the wall of the oven, if they do, you will have to pull out the range from the wall and retrieve them! ( I used two surgical hemostats for this.)
4TH..disconnect the old element, connect the new one....
5TH..Gently slide element back in place, replace sheet metal nuts.
6TH..reset circuit breaker

I shut off power at electrical box.
Then I removed 4 screws on back to expose connector enclosed in insulation.. It was not necessary as when I removed 2 screws in oven and pulled element out , the element came out far enough to disconnect easily and slip the element into electrical unit.
15 minutes start to finish..

It was so eazy that I didn't have to ask my husband how to do it.

slid it into the oven easy as pie

impossible to repair, I would need to dis-assemble at least half of every part of the stove to get to where the element plugs in.

I removed the two screws in the oven and then pulled the stove out to remove the center back panel. This was easy to do once I found the right sized socket. Next I removed the two electric connections from the broken baking element and removed it from the oven. After I cleaned the oven it only took a couple of minutes to install the new baking element (connected the two electric connectors, screwed the two screws in the back of the oven, and replaced the back center panel). After that I plugged the oven in and tested the oven and it worked perfectly. Thanks for getting my new baking element to me so fast.

1) unplug range (range is 220volts, please be careful)
2) remove back panel
3) unplug wires from bake element
4) remove 2 5/16 bolts from mounting braket inside oven
5) pull out broken element
6) reverse steps to install new element
7) turn on oven and observe new element for proper operation.

I removed the old element and replaced it with the one that I ordered from Parts Select after reading your easy to follow instructions. I'm a 62 year old woman and it really was quite easy. Just make sure all electric sources are disconnected the breaker is off and follow the directions. The repairman would have charged me a minimum of $225. I did it my self for $60.00.

Removed the bolts that were attached and gently pulled the element out. Removed the attached wires. Attached the wires to the new element and slid back up inside and tightened with bolts.