Models > 79046139300 > Instructions

79046139300 Kenmore Range - Instructions

Jump to:

All Instructions for the 79046139300

Customer:: Robert R from Lewistown, PA
Parts Used:: 5304505695
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins

Two of theTop gas burners would not spark

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sue from Lampasas, TX
Parts Used:: 5304409888
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sharon from Foley, AL
Parts Used:: 5304524341, 316538904
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from Glasgow, MT
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Was this instruction helpful to you?

Customer:: Gerald from Artesia, NM
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Was this instruction helpful to you?

Customer:: Jeffery from Union Point, GA
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Was this instruction helpful to you?

Customer:: Franklyn from Jupiter, FL
Parts Used:: 318041603
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Cracked inner door glass

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper oven heating.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Was this instruction helpful to you?

Customer:: Jack from Hedgesville, WV
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Heating element burned out

Took screws loose, unplugged old one plugged in new one put screws back

Was this instruction helpful to you?

Customer:: Catherine from San Saba, TX
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Bottom element in oven not heating.

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

Was this instruction helpful to you?

Customer:: Richard from Oro Valley, AZ
Parts Used:: 318255605
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

broiler element burned out

watched a U-Tube video on this subject.....worked like aa charm!!

Was this instruction helpful to you?

Customer:: BETSY from HENDERSONVILLE, NC
Parts Used:: 318053103
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door gasket was worn, stained and needed replaced

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Was this instruction helpful to you?

Customer:: Constantine from Vero Beach, FL
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Was this instruction helpful to you?

Customer:: WILLIAM from RIDGE, NY
Parts Used:: 318254699
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

end caps that hold the stove at proper depth and support control panels broken

repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.

Was this instruction helpful to you?

Customer:: Russell from North Smithfield, RI
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Oven did not work since bake element did not warm up.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Was this instruction helpful to you?

All Instructions for the 79046139300