79094222408 Kenmore Range - Instructions

I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.

Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.

unplugged old burner plugged new one in

Took old one out and plugged the new one into place.

Removed 2 screws at rear of bottom panel. Removed old panel, replaced with new and screwed back in.Piece of cake. Plus this company was great to order from. received part the same day. Very happy. Would order through this company again.

I removed two screws and lifted out the ruined bottom. I set the new bottom in, but could not get the screws lined up so left them out. The bottom is heavy enough, it is not going anywhere. I am very grateful the part was available.

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

Simple just remember there is a hinge lock on the hinge just open the door reach down to hinge and lift lock it blends in but its there close the door and pull out the door pull 2 screws on the hinge connecting it to door install new hinge

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.

Removed outer glass first ,then worked my way thru to inner glass..

Talked to someone who knows , DX'd the potential problem,looked for the part on your very user friendly website and your DX was exactly what my oven was doing, when the Thermo-Sensor arrived, I unplugged the oven, removed the metal back, took out the faulty Sensor, replaced it very easy then realized the plug was different, so called a friend who knows how to Solder and 2 hrs, later, my oven was repaired and I began baking an Apple pie to repay a friends kindness The pie was perfectly baked , my friend was happy and so am I ,the baker, just before the holidays Thank you Parts Select for helpful DX and speedy delivery - seems you saved Christmas for me.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.