79045489500 Kenmore Range - Instructions

Husband made install in very short time. Nice to have them back in operation.

Very simply following the online video instructions.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

In order to service the switches on this model, remove all four knobs for the switches. This will expose the plastic nuts which hold the fascia panel secure. Remove those nuts and the fascia panel. Next use a phillips screwdriver to unsecure the steel panel which secures all four burner switches. Remove the faulty switch, taking note of each color lead and terminal designation. Replace in reverse order.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Turned off electrical breaker (double). Removed the switch handle, removed the plastic rings (special wrench) under the handles. Removed three screws up under the front of control panel. Removed six screws holding the infinite switches. Removed defective switch. Different from the new switch. Wiring locations were different on the old sw. The reason for the vom use. All is well.

After searching to find the right part to replace this i found this company on line. I still could not find the part so contacted them directly and the nice woman who answered found the exact part we needed. It was shipped to us in perfect condition and we did the install ourselves with the installation help that was included with the part. We are so thankful we found this company and were able to fix our broken door. Would recommend them very highly.

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.

Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.

I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

watched a U-Tube video on this subject.....worked like aa charm!!