79070119706 Kenmore Range - Instructions

Once I recieved the new part it was easy to determine what two screws to remove to remove both the panel and the handle. I removed the two screws, slid the panel up and removed it. The new panel locked into place when slid down over the door and I replaced the sctews.

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.

I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.

remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble

Open the door and slide in the new rack.

removed 2 screws from inside oven door swap out old to new handle reinstall 2 screws done less than 15 min.

YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made it more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

PartsSelect.com saved me lots of $$$$$. I have had appliance repairers come and view the stove and tell me I needed so much work. I paid them and the stove still wasn't fixed. I figured out the problem and found PartsSelect.com = savior!

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.