7909621440B Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ruben from moss point, MS
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
range top left big burner would not come on.
I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvie from Pasco, WA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
replaced the infinite burner switch
I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Newport,, NC
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch was sparking
Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARGARET from MILFORD, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would not heat up
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Montpelier, IN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner would get hot, but would not turn down.
To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Glenmoore, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
element light staying lit
Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Lithonia, GA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner stays on when switch is in the off position.
Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Acton, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner would stay on and the hi-temp safety limit switch is all that would shut it off.
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Forestdale, MA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Large burner doesn't turn down or shut off.
Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Krista from Newtown, CT
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
inner glass uncleanable
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newark, DE
- Parts Used:
- 316203301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from BENTONVILLE, AR
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner would no turn off.
A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Miles City, MT
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Large burner switch made popping and buzzing noises.
The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hollypond, AL
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Cracked inner oven door
Removed outer glass first ,then worked my way thru to inner glass..
Was this instruction helpful to you?
Thank you for voting!