79094213407 Kenmore Range - Instructions

replaced it

First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

remove back panel took out old part splice wire replaced

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Received the new part FAST. Ordered online. Easy to plug in the new part. Will use PartSelect.com again when needed to order parts!

Easy as 1-2-3

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.

Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.