79090814405 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ERIC from INDIANAPOLIS, IN
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inside glass
Followed your video and it was not hard at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Florence, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Jacksonville, FL
- Parts Used:
- 5304506004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inside glass window panel had cracked.
It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maldon from Burlington, NC
- Parts Used:
- 5304506004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The inner glass was cracked on the oven door.
I removed the four phillips screws to seperate the oven door sections (that lets the door handle drop off too.) and then took out four hex head screws that hold the glass bracket in place. I had to lift out the front glass to reach the broken back glass. After that, I just slipped the new glass into position and reversed the procedure. It took about 25 minutes. It took just about 25 minutes counting the time it took me to find a hex head nut driver. I'm willing to bet it saved me a bundle, too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Ocala, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
originaldrawer guide was cruched out of useable shape
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from WEST UNION, OH
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One guide was missing and the other was broken
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Hauppauge, NY
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
over draw was off track
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners constantly overheating, and inconsistent heating.
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repair took less than 10 minutes. Incredibly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Poteau, OK
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven drawer would not open or shut completely
first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHELLE from STOUGHTON, MA
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer glides were snapped off
The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from WABASH, IN
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One Of The Front Drawer Guides Broke
Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from ST Joseph, MN
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Storage drawer hard to open and was hanging down on one side.
I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from KERSEY, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
sparking element
removed back and transferred four wires to new part and replaced back
Was this instruction helpful to you?
Thank you for voting!