Models > 79070291404 > Instructions

79070291404 Kenmore Range - Instructions

Jump to:

All Instructions for the 79070291404
46 - 57 of 57
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from Greenville, TX
Parts Used:
316239700
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diane from Natrona Heights, PA
Parts Used:
316239700
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
55 yr old wall oven had burnt out seal
Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fanny from Alhambra, CA
Parts Used:
316468601
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
I had the top trim broken on the oven door.
Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from North Bend, OR
Parts Used:
316088600
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Inner Glass in the oven door was broken
Removed the door and carefully dismantled all of the layers. In my particular situation, I needed to do some high heat painting as over the years the white panels had discolored due to heat. So, I had to wait a day or so for the painted panels to dry--but they looked great when done. Some words of caution, really look the diagrams over and be sure you are ordering the correct glass (there are three and all different). I initially ordered the wrong one but used it anyway as it replaced a badly stained one. But, I had to re-order the correct glass. It was amazing how quickly I got both orders, though. Only took a couple of days!! So, am very pleased with the way it looks--like new again and quite easy if done systematically!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Manasquan, NJ
Parts Used:
316495901
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
Customer:
KAREN from INDIANAPOLIS, IN
Parts Used:
316088600
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
inside oven glass had cracked.
I got the ex husband to come over and take it apart and fix it, he said that it was a really easy repair to complete.
Was this instruction helpful to you?
Thank you for voting!
Customer:
GARY from LIBERTY, MO
Parts Used:
316088600
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken inner glass panel in oven
Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inner glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lauren from Delta Junction, AK
Parts Used:
316032411
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven would not maintain heat
We took out the old thermostat and replaced it with the new one....now we don't have to buy a new oven!!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Conway, SC
Parts Used:
3203459
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
put the safty valve in
turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Holly, MI
Parts Used:
316032411
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
oven was not heating up to the right temps.
removed the old thermostat and replaced it with the new one. now it works great!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe De from Montgomery, AL
Parts Used:
3017142
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Foul ordor coming from stove
The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Corpus Christi, TX
Parts Used:
316468601
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken door trim
simple to unscrew the door handle from the inside, remove the broken trim, place new trim on, clamp the door together, then screw the handle back on. Went well!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79070291404
46 - 57 of 57