79095393901 Kenmore Range - Instructions

Easy as 1-2-3

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

Large burner would cycle on and off per temp setting a few times. Then it would stick on high. Read other problems people had with the burner switch, which helped to determine the problem. Instillation per video was pretty straight forward; but the issue I ran into was when pulling off the wires from old switch, there was a short wire which connected to the indicator light. The abrupt release yanked the wire which caused the lens indicator to snap. So, when you are repairing the switch, be aware if there is enough slack in the wires to prevent that issue

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.