79090212012 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerry W. from Oxford, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element bad, broiler element OK.
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Summerville, SC
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My five-year-old Frigidaire Gas stove was giving an F 10 code.
I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from S CHESTERFLD, VA
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat
Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from GREELEY, CO
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element burned out
All you do it unplug the old one and plug in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dineshbhai from Rincon HWY21, GA
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
N/A
I had open back cover and remove the switch than replace new switch. Makesure cable conection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from WEATOGUE, CT
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original Element physically broke
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from CINCINNATI, OH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel rusted away
Removed two screws removed and replaced panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MAINEVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element went out
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from MARIETTA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from Germantown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element broke
It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!