79097433801 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Palm City, FL
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range displayed error code F10
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from CINCINNATI, OH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel rusted away
Removed two screws removed and replaced panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from MARIETTA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACY from NEW PHILA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Many thanks to PartSelect for their comprehensive website and fine service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELKHORN, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
I will have to toss out this stove and buy new as you and no else has this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from MENDON, NY
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom panel burned through
Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from OWASSO, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dudley, MA
- Parts Used:
- 316462878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven not working
Disconnected power and removed rear panels. Went through basic troubleshooting of oven safety switches and controls. Determined problem was control board. Removed control board and ordered replacement.
Removed control board’s faceplate by carefully separating it from board with utility knife. Installed faceplate on new control board (stick on) and installed board into control panel. Reinstalled rear panels and reconnected power.
Verified oven operation.
Removed control board’s faceplate by carefully separating it from board with utility knife. Installed faceplate on new control board (stick on) and installed board into control panel. Reinstalled rear panels and reconnected power.
Verified oven operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from LAKELAND, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom oven pan was warped and discolored
Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from AUGUSTA, ME
- Parts Used:
- 316430900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Element burned out
Turned off power at breaker, took back off range, removed red and blue wires, removed oven door, removed two screws holding in broil element, removed wires supporting old element, installed new element and reversed procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Colchester, CT
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element would not heat up
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from FAYETTEVILLE, NY
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not reach temperature or it would finally reach temp but would not stay warm.
Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deane from WINCHESTER, KY
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temp. probe
Easy watched on line video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from CHELSEA, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a F31 code which means oven isn't working
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
Was this instruction helpful to you?
Thank you for voting!