79078583402 Kenmore Range - Instructions

I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh

Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.

Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...

This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repaired our stove myself!

after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com

From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than it had for some time.

Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

removed the old igniter, installed the new one. 15 minutes, piece o cake!

First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!

the igniter is real easy to put in