79096423403 Kenmore Range - Instructions

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!

This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.

Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.

Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.

After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Removed outer glass first ,then worked my way thru to inner glass..