79095033502 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dineshbhai from Rincon HWY21, GA
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
N/A
I had open back cover and remove the switch than replace new switch. Makesure cable conection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from KNIGHTDALE, NC
- Parts Used:
- 316203200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broiler broke apart in pieces. Also we found an round honeycomb part
in the bottom of the oven when I was looking to see what was going on. My husband did the repair just as the video described. I suspect this part honeycomb round maybe ceramic piece goes over where the heat is vented from the oven. Where do I get another one of these and how does it attach in the oven-under the burner. HELP I tried to look on the schematics and did not see anything. The repair went fine, except when we turned everything back on it did not work. Then my husband remembered he forgot to plug the new part IN. Once plugged in it is working fine. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Clearwater, FL
- Parts Used:
- 316067902
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I forgot to remove something I had saved in the oven, planning to remove it before using the range.
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Toms River, NJ
- Parts Used:
- 316468601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Cap On The Range Door Broke
There were only 2 screws that held the door handle & cap in place, removed screws & handle to get cap pieces off. Ordered new cap, - lost screws - cap delivered - no screws had to order screws, damn! They're expensive too !! Got screws, installed handle & cap, now wife is happy again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from FRUITHURST, AL
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosetta from COLUMBIA, VA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
problem pulling out bottom tray on range
just put in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
burners 1 would not do anything burned out 2 when from normal to out of control heat would not keep a constance heat
turned off breaker 3 Phil screws open door and on inside range top I would reconmend a board to hold top up square tip for cross bar and pliers to pull wires off fit perfect works really nice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from RESTON, VA
- Parts Used:
- 389082702
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace the dual-element burner in glasstop range
The how-to video was helpful, though my old range has an extra spacer panel between the glass-top and oven, requiring an extra couple of screws to be removed, with different-sized Philips head.
1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.
2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.
3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.
Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.
The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.
1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.
2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.
3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.
Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.
The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from SOLANA BEACH, CA
- Parts Used:
- 316455420
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Black frame cracked / disintegrated
The thin black plastic frame around the old one had become brittle and cracked/disintegrated. So, nothing to hold the functioning unit to the frame.
All I needed was a new frame.
The one that was shipped was the wrong model number, so it is useless to me.
I will be returning it for a refund.
Thank you for trying, so sorry, no cigar.
Best, Bill Elliott redbeds77@gmail.com 760-505-8009
All I needed was a new frame.
The one that was shipped was the wrong model number, so it is useless to me.
I will be returning it for a refund.
Thank you for trying, so sorry, no cigar.
Best, Bill Elliott redbeds77@gmail.com 760-505-8009
Was this instruction helpful to you?
Thank you for voting!
Broken right side parts for lower over storage drawer.
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Jacksboro, TN
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer slide
Remove drawer. Insert new slide. Install drawer.
Was this instruction helpful to you?
Thank you for voting!