79094111405 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daivid from North Attleboro, MA
- Parts Used:
- 316442301, 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner wont heat all of the time
removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Ashton, IA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burner wouldnt heat
removed element , cut wires, conected wires,replaced element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lewis from COLDWATER, MI
- Parts Used:
- 316400601
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Aluminum foil accidentally put on bottom panel ....burnt up, left non removable residue.
After 15 minutes of frustration and back breaking I removed the oven door and had much better access to the panel, from there on it was all down hill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Castle Rock, CO
- Parts Used:
- 316490001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would kick off after preheating to temp.
Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fort Myers, FL
- Parts Used:
- 316203200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broil element was bad.
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Brunswick, GA
- Parts Used:
- 316445501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Gaffney, SC
- Parts Used:
- 316203200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom elerment burnt into
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Warsaw, VA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken lens over oven light
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from RHINELANDER, WI
- Parts Used:
- 316400601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Aluminum foil baked on surface
Took out 2 screws, removed panel.
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from N MYRTLE BCH, SC
- Parts Used:
- A316222301, A316222201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
showing age
bought drip bowl from big box store and the 8 inch did not fit . yours fit perfect will use you for future diy jobs thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melinda from Three Rivers, MA
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Rusted leveling foot
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!