62960008601 Kenmore Range - Instructions

easy to put in

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

Removed 2 phillips head screws, disconnected the 2 wires. Installed new element, connected wires then installed screws. Took less than 3 minutes. What i liked was how fast I received the new element. Ordered online on Friday around 12:30 and received Saturday morning by 9:00 AM. Excellent transaction!

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Make sure you unplug your stove before you start! You should probably shut off the power at the breaker box too.

Since the upper oven is so small, I found that I couldn't reach the connectors well enough to work with them. So I pulled out the whole oven, took the screws off the back cover and from the back I was able to easily reach where the wires connected to the element. Then it was a piece of cake.

Just use a small knife to unbend the little metal things that hold on to the metal ends of the element. Slide them on to the new element, and crimp them tight with pliers.

Oh, you also have to take off the bracket on the ceiling of the inside of the oven to get the old element out, and the new one in.

The oven has been working great!

Repair would have only taken minutes, but upper support plate screws were rusted and almost fused to the plate. Once the plate screws were out (had to pry plate out) installation was done in 3-5 minutes.

As for the replacement part, worked perfect on the first try. Very happy with price, speed of delivery and preformance.

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

Turned off breaker to oven, removed racks, unscrewed the plate holding the element in place, and pulled out the wires a few inches. All easy and fine to this point. Never having done anything like this before, I wasn't sure HOW the element was attached to the wires, so tugged on them a bit, but nothing budged. Got a flashlight (it got dark in there with the upper part of my body in there)looked again, but still couldn't tell. Referred to this site and saw reports of "plug and play", went back and examined the ends more closely on old and new element, realized that they slide straight on and straight off in a "sleeve". Got some pliars and pulled the ends apart. Slid the new end on to one wire, but couldn't get the other one on until I realized I had crushed it a bit with the pliars. Reopened the "sleeve" with a vegetable knife and slid the other end of the element into the "sleeve" at the end of the wire. Then pushed the wires back in and screwed plate on. It took about 23 minutes, and that included time to look up this site and do some reading, jump up to find a flashlight, and jump up and find a pair of pliars. My hubby was out of town for 3 weeks and suggested I wait til he got home--glad I didn't wait.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

PULLED THE POWER CORD!! Loosened a couple of screws holding the element to the rear oven wall, removed the electrical wires (red on left, yellow on right) attached to the baking element, removed old element, inserted new element and reattached the wires respectively thereto. One minor glitch did occur. The RED wire inadvertently slipped back through the hole into the insulation and was not retrievable. I removed the small metal plate housing the wires on the back bottom of the stove, pushed the red wire (plentiful length) back into the oven, reinstalled the plate, connected the red wire to the bake element, reconnected the power, element began to heat. Mission accomplished. One caution: Pay attention to the SHAPE of the failed element before ordering online or buying in person.

See description listed as problem