79078530600 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donnie from McLaughlin, SD
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven was too hot code f-10 came up
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from petaluma, CA
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace lower oven floor
removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Suttons Bay, MI
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Men Should Not Use The Oven
Delivery was fast. Two screws to remove the old oven panel. Slipped in the new panel and tightened the screws with my fingers. Job completed. It was as easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Trinidad, CO
- Parts Used:
- 5304534663
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
bake burner igniter open circuit--no oven heat
I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that remained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Mansfield, MA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from AuGres, MI
- Parts Used:
- 5304534663
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven would not stay on
remove belly pan ,pull draw out easy acsess remove screws and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- darwin from Wylie, TX
- Parts Used:
- 5304534663
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Oven would not turn on.
Gas stove worked, as well as brolier, but oven did not turn on at all. Replacing the bake igniter part did the trick. It is a simple operation, 30 minutes tops normally. In my case the screw was originally installed a little crooked and had caused it to strip and wouldn't come out. As a result, I had to also remove the gas pipe that the igniter was attached to in order to forcibly remove the screw and detach the old bake igniter. This is what caused the extra time and difficulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Gladwin, MI
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
burner would not light
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Was this instruction helpful to you?
Thank you for voting!