79094354701 Kenmore Range - Instructions

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

I removed two screws and lifted out the ruined bottom. I set the new bottom in, but could not get the screws lined up so left them out. The bottom is heavy enough, it is not going anywhere. I am very grateful the part was available.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

I followed the Parts Select Video that showed replacing an identical switch. Mine were another brand & style with different color wires. I took a picture of 1 to keep track of the wiring and removed it. I saw that the terminals were marked P, H1, H2, L1, & L2 so I put the wire from the same terminal onto the Parts Select switches & they work just fine now. The parts I got from you are heavier and a much better quality than the original equipment. I would also like to say that I was amazed at how fast this order was shipped, and the washer pump was a piece of cake thanks to your video.

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

Removed 2 back screws, lifted pan from rear and pushed front slightly forward/into oven until front lip cleared. Installed new pan in reverse order.

After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Replaced control units that were malfunctioning.

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.