79079362406 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Suttons Bay, MI
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Men Should Not Use The Oven
Delivery was fast. Two screws to remove the old oven panel. Slipped in the new panel and tightened the screws with my fingers. Job completed. It was as easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Minooka, IL
- Parts Used:
- 5304475129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
foot on burner grate broke
Just pushed the new rubber foot into the hole. Took about 10 seconds to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from petaluma, CA
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace lower oven floor
removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from AuGres, MI
- Parts Used:
- 5304534663
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven would not stay on
remove belly pan ,pull draw out easy acsess remove screws and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patti from Greer, SC
- Parts Used:
- 5304503232
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked inside glass
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- darwin from Wylie, TX
- Parts Used:
- 5304534663
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Oven would not turn on.
Gas stove worked, as well as brolier, but oven did not turn on at all. Replacing the bake igniter part did the trick. It is a simple operation, 30 minutes tops normally. In my case the screw was originally installed a little crooked and had caused it to strip and wouldn't come out. As a result, I had to also remove the gas pipe that the igniter was attached to in order to forcibly remove the screw and detach the old bake igniter. This is what caused the extra time and difficulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LYLE from FARMINGTON, NY
- Parts Used:
- 5304534833
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Bottom of Trim has rusted and looked really bad.
Replaced the trim. Removed the handle and then the glass along with the old trim piece. Had to work at getting the old trim off as the rest had really wedged the glass in. Cleaned the glass, applied new 2 sided adhesive tape to hold the glass in place. Reinstalled the glass/trim and the door handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hollypond, AL
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Cracked inner oven door
Removed outer glass first ,then worked my way thru to inner glass..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Bowie, AZ
- Parts Used:
- 316490001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Oven turning off ater Pre- Heating
Talked to someone who knows , DX'd the potential problem,looked for the part on your very user friendly website and your DX was exactly what my oven was doing, when the Thermo-Sensor arrived, I unplugged the oven, removed the metal back, took out the faulty Sensor, replaced it very easy then realized the plug was different, so called a friend who knows how to Solder and 2 hrs, later, my oven was repaired and I began baking an Apple pie to repay a friends kindness The pie was perfectly baked , my friend was happy and so am I ,the baker, just before the holidays Thank you Parts Select for helpful DX and speedy delivery - seems you saved Christmas for me.
Was this instruction helpful to you?
Thank you for voting!