79096613409 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from floyd, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
8" burner would get red hot (High) with knob set on 4 or 5, them cool back down to the correct setting. In a few minutes it would be red hot again.
Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Van, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burners on high all the time.
Replaced control units that were malfunctioning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Corpus Christi, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would stay on high when switch was on simmer
Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Montpelier, IN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner would get hot, but would not turn down.
To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Glenmoore, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
element light staying lit
Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Acton, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner would stay on and the hi-temp safety limit switch is all that would shut it off.
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Kingsport, TN
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Large element would only heat on high.
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from BENTONVILLE, AR
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner would no turn off.
A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Newport,, NC
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch was sparking
Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arnold from Carlsbad, CA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
element would not heat.
Replaced the control I got from you , even though it was a little different the lugs matched up and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from cana, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the stove eye would go to high and stay
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hemet, CA
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
really bad ugly streaks inside of glass
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Mansfield, MA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Was this instruction helpful to you?
Thank you for voting!