79075721992 Kenmore Range - Instructions

Piece of cake. Fit like a glove. Thank you

removed face screws from drawer. Previous poster described our problem exactly- middle screw on drawer pull had come loose and fallen down, which probably caused the pull to break in the first place, just as his had done. Replaced handle- very easy and like brand-new. Great site- easy to navigate and find the right parts, very fast shipping.

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

Remove 8 #2 Phillips Tipped Machine Screws from exterior sides of oven door. Remove Shell/FrameClean. Clean any remaining glass/debris. Insert new glass into frame. Install frame onto oven door. Install screws.

Time saving tip. Clean all surfaces including interior glass beforehand for best and fastest results.

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I thank PartSelect for providing great service and assisting me in my time of need.

Marv Dixon

Disconnect power supply,reemove upper back panel,pop otut old switch,disconnect it ,connect new switch ,snap in place ,screw uppper back panel back in place,reconnect range power supply.

switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.