79090900602 Kenmore Range - Instructions

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

Touch up paint was easy to apply. I gave it a few coats and you cannot tell where to chip was. I wish you had a standard mail delivery option. I paid twice the price of the paint for fed ex delivery. I didn, t need the paint next day but it did get here before the estimated deliverydatee.

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

Replaced control units that were malfunctioning.

simply unplug the old burner and plug the new one it. not many repairs this easy. the best part of the whole thing is that the part arrived the next day.

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....