79060042402 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- elizabeth from Pasadena, MD
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner coil had been broken
Just plugged it in! The hardest part was finding the model number. It was inside the top of the stove,while cleaning, I found it-on the left hand side when you take out the burner pans. I searched this site, found the part and when it arrived I just plugged it in and it worked fine. I would say less than 5 minutes to fix this issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greenville, TX
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from OKLAHOMA CITY, OK
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
gross drip bowls on range when we bought the house
The new drip bowls are beautiful, fit perfectly. Person I spoke to when there was a bit of mix-up in delivery was exceptionally wonderful! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from El Paso, TX
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just had to replace the racks in the stove.
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Natrona Heights, PA
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
55 yr old wall oven had burnt out seal
Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Valley Cottage, NY
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner burnt
It was just replacing the element no tools were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from East Point, KY
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My original drip bowls were rusty and ugly on the two front burners.
I removed the old drip bowls from the top of the stove and replaced them with the new ones. I am not a handy person but even I had no problem doing it as I regularly remove them anyway to put them in the dishwasher to clean them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Mt. Vernon, AL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rusty worn out oven racks
Removed the old oven racks and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl K from Klamath FAlls, OR
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heating element would not sit level with generic drip bowls
I replaced the generic drip bowls with the ones I ordered here and the work perfectly. The heating elements now sit level and I am very happy with them. Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Fossil, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced burner block
Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Athens, OH
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element burned out
simply unplug the old burner and plug the new one it. not many repairs this easy. the best part of the whole thing is that the part arrived the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Virginia Beach, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old element worn out
Removed old element and plugged in the new. Very simple and easy. Shipping and delivery was amazingly fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Arena, WI
- Parts Used:
- 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Bowl Replacement
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- raymond from Wilbur, WA
- Parts Used:
- 316442300, 5303935058, 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burner not comming on
unpluged stove pulled offback of stove behind buner controles took knob off burner switch took off two screws switchout put new switch in then took wires one at a time off and put on new switch put backon pluged in it worked
Was this instruction helpful to you?
Thank you for voting!