79046599503 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from KALISPELL, MT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from AVON, NY
- Parts Used:
- 903136-9010
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Burner control failed, needed replacement
Drawings on web site somewhat hard to read, resulting in more
disassembly than actually necessary. Turns out, simply removing the
threaded plastic securing rings around the bases of the controls frees
up the faceplate, and allows access to the phillips screws that hold down
the bracket. Then it's a simple matter to replace the control unit by
swapping out the leads one at a time from old to new. Be careful when
re-attaching those plastic securing rings, they can cross-thread pretty
easily.
disassembly than actually necessary. Turns out, simply removing the
threaded plastic securing rings around the bases of the controls frees
up the faceplate, and allows access to the phillips screws that hold down
the bracket. Then it's a simple matter to replace the control unit by
swapping out the leads one at a time from old to new. Be careful when
re-attaching those plastic securing rings, they can cross-thread pretty
easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from YOUNGSTOWN, FL
- Parts Used:
- 318191023
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dual infinite range switch on left front burner of glass top range would stay on full high no matter what setting was selected on the burner knob.
Remove 4 knobs from front of stove.
Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.
Remove front cover.
Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you hook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.
Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.
Remove front cover.
Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you hook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- German from SELLERSBURG, IN
- Parts Used:
- 5304533520
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Center of dual burner was broken
Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from PONCE INLET, FL
- Parts Used:
- 903136-9010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken burner switch. Would not shut off.
Turn off breaker to the oven. Removed four knows by pulling them up and out. Using either a large flat blade screwdriver or adjustable wrench (depending upon stove top model) remove threaded style holders at each burner switch control to remove the glass clock control top panel. Remove glass panel and note ldgasket position. Place glass panel on top of stove top on a cloth towel to prevent scratches. Remove 8 screws and remove/lift up burner control assembly. Invert and place on its side to gain access to broken contol switch. Took a picture of wiring and close up off switch to help remember where each wire plugs into switch. Remove 2 Phillips screws from the old switch and remove from panel. Using a flat blade screwdriver gently remove one wire at a time and using knob to orientate the off position of the new switch. Remove each wire one at a time and install on the new switch. Compare numbers on both the old and new switch to assist where each wire goes. The numbers are beside each terminal and using a flashlight and magnifying glass will help making the job easier. DO NOT mix the wires up. Use the 2 longer screws and threaded bracket supplied fasten the new switch to the glass panel. Reinstall the glass panel using the screws removed and thread on clips at each switch and tighten using a large flat blade screwdriver. Be sure to route the wiring to not pinch the wires and install the gasket along the front edge which fills the gap along the burner top and side for a tight seal keeping water and food particles out. The infinite control switch has letters such as H1, H2 etc as the switch fits several models with different wiring diagrams and colours so it's impt to note this when transferring the old wires to the new switch. Also the gasket along the top glass edge ensure to note exactly how it is placed to reinstall to be exact when you reassemble. Replace the 4 control knobs by pushing them on after aligning to fit as they were removed. New switch should be positioned the same as the others with off at the top and a notable click. Be sure to note this when transferring wires from the old to new switch. Turn breaker on. Note: If you have minimal skills this should be left to someone who is an electrician or has repair experience in this field.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from MORGANTOWN, WV
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
2 elements stopped working.
My husband followed the video instructions and it was easy to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CORDOVA, TN
- Parts Used:
- 318255401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out element
removed replaced in lest than five minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOBILE, AL
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When oven was set at 400, actual temp would run about 285.
1 Turned off the oven breaker.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Little Silver, NJ
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Error Code F1
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everette from HARRISBURG, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat. Didn’t cut off at set temp
Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.
Saved $150 on a service repair call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from FOREST HILLS, KY
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would start to heat then quit,checked the temperature sensor with ohm meter after cool down reading about 1100 ohms. I cleaned connection tried it again seemed to work well but quit again in just few days.
Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great
OEM parts plug in same, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!