79096549600 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from Hillsboro, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch was Sparking
So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Warfordsburg, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
burner switch burned out
Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Madison, AL
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Hot Surface Light won't turn off.
Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Van, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burners on high all the time.
Replaced control units that were malfunctioning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Wimauma, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Purchased home where previous owner melted Aluminum Foil to bottom panel of oven.
Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Mosier, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
front left burner was on HI no matter what the dail setting was
pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Forestdale, MA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Large burner doesn't turn down or shut off.
Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Miles City, MT
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Large burner switch made popping and buzzing noises.
The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvie from Walnut Cove, NC
- Parts Used:
- 316436000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
shorted out small element burner switch
First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Acton, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner would stay on and the hi-temp safety limit switch is all that would shut it off.
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Krista from Newtown, CT
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
inner glass uncleanable
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newark, DE
- Parts Used:
- 316203301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellyjean from Springfield, MA
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burned out.
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Mansfield, MA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Was this instruction helpful to you?
Thank you for voting!