79091039402 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- greg from SANDY, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burner switch failure
Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from W SAND LAKE, NY
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8" burners were not responding correctly to the switches
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from UNION, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lois from middletown, DE
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
interior oven door glass cracked
All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from CHEWELAH, WA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vito from RED BANK, NJ
- Parts Used:
- 5304506004
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
shatered inside oven glass panel
I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FREDERICKSBRG, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgiana O from E MONTPELIER, VT
- Parts Used:
- 316442300, L304430992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement
remove old, set in new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from CLYDE, TX
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old bowls were rusted beyond ability to clean
Put the new bowls under the stove top burners with disposable liners to protect them. They look very clean and shiny now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from MONTANA CITY, MT
- Parts Used:
- 3051162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
guide was broken
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEWISTON, ME
- Parts Used:
- 316225001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken element
I followed instructions on your video. Took 10 minutes. My wife thought I was a pro.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LANOKA HARBOR, NJ
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!