79097432800 Kenmore Range - Instructions

replaced it

Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?

1. Order part
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.

I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Removing the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

Easy as 1-2-3

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Unscrewed the oven bottom plate and removed. Put new one in place and screwed it in place. Stove looks brand new again and am so happy with the results.The part we received was a perfect match and arrived in a few days!

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.

Removed 2 back screws, lifted pan from rear and pushed front slightly forward/into oven until front lip cleared. Installed new pan in reverse order.

After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!

It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.