79096423408 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roy from Kingsport, TN
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Large element would only heat on high.
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from cana, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the stove eye would go to high and stay
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Columbia, SC
- Parts Used:
- 316555800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner wouldn't heat up
I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Newport,, NC
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch was sparking
Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARGARET from MILFORD, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would not heat up
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from Pensacola, FL
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No current to the burner
Checked the burner and no power to heat the burner. removed the old switch and put on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Pleasant Mount, PA
- Parts Used:
- 318198825
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The warning light for the warmer was stuck "on"
Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Lithonia, GA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner stays on when switch is in the off position.
Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from Huntington Station, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replaced large burner switch on tappan range
I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Forestdale, MA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Large burner doesn't turn down or shut off.
Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donnie from McLaughlin, SD
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven was too hot code f-10 came up
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LITCHFIELD, CT
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad burner switch
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Mosier, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
front left burner was on HI no matter what the dail setting was
pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, SC
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Control Rod On Switch Was Broken Off
I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Peoria, IL
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Infiniti switch needed to be changed.
Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.
Was this instruction helpful to you?
Thank you for voting!