79094219409 Kenmore Range - Instructions

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Simple just remember there is a hinge lock on the hinge just open the door reach down to hinge and lift lock it blends in but its there close the door and pull out the door pull 2 screws on the hinge connecting it to door install new hinge

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Talked to someone who knows , DX'd the potential problem,looked for the part on your very user friendly website and your DX was exactly what my oven was doing, when the Thermo-Sensor arrived, I unplugged the oven, removed the metal back, took out the faulty Sensor, replaced it very easy then realized the plug was different, so called a friend who knows how to Solder and 2 hrs, later, my oven was repaired and I began baking an Apple pie to repay a friends kindness The pie was perfectly baked , my friend was happy and so am I ,the baker, just before the holidays Thank you Parts Select for helpful DX and speedy delivery - seems you saved Christmas for me.

Removed outer glass first ,then worked my way thru to inner glass..

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.