79096542602 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deane from WINCHESTER, KY
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temp. probe
Easy watched on line video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from CHELSEA, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a F31 code which means oven isn't working
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WATERTOWN, MA
- Parts Used:
- 5303935318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Handle
1. Order part
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willis from Friendsville, TN
- Parts Used:
- 5304467898
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Convection fan making noise
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal was worn and did not seat properly. It leaked heat.The infinite burner was not warming in the low heat positions
I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patti from Greer, SC
- Parts Used:
- 5304503232
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked inside glass
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from wakefield, RI
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
aluminum foil melted on oven bottom
It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LITCHFIELD, CT
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad burner switch
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W3Works, from Fairport, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner switch would not disengage, leaving +24VAC to the element.
Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Sun City, AZ
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner Switch Shorted Out
Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.
Was this instruction helpful to you?
Thank you for voting!