79092314305 Kenmore Range - Instructions

Removed four srews from bak of the oven so I could get to the timer. Then I unplugged the oven swapped out the wires put everything back together. Plug it back in and started the oven. Work great. Also you must remove the timer faceplate carefully or you will peel off the white.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

After receiving the parts in only two days, I first turned off the circuit breaker. Then I pulled the stove out from the wall. I used the nutdriver to remove the upper rear panel. Using the screw driver I removed the defective clock timer and used a pocket knife to carefully remove the clock timer face. I positioned the clock timer face on the new clock timer and installed same in the stove panel. (I had made a list of the wires and their colors to insure the proper placement on the new clock timer). Installed the four screws and on to the burner switch. Two front panel screws removed and the defective burner switch was out. Installed the new burner switch, connected the wires, installed the two screws, pushed on the knob and I was ready to go. Re-installed the reap panel, pushed stove back in, turned on the circuit breaker and tested the burner and oven. All worked correctly. A very easy repair!

Removed the backing, removed the old part and disconnected the wires (after taking a quick photo so we knew where to reconnect them on the new part). Removed clock/timer facing and placed on new part. Reconnected the wires to the new part and screwed it back in. Oven now works great without spending the $300 we were quoted by the repair man!!

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

I am 78 years old and I watched the how to video twice and then did it so if I can do it anyone can,oh and I am a woman

in the bottom of the oven when I was looking to see what was going on. My husband did the repair just as the video described. I suspect this part honeycomb round maybe ceramic piece goes over where the heat is vented from the oven. Where do I get another one of these and how does it attach in the oven-under the burner. HELP I tried to look on the schematics and did not see anything. The repair went fine, except when we turned everything back on it did not work. Then my husband remembered he forgot to plug the new part IN. Once plugged in it is working fine. Thanks

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

I follow the video on your site

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.