66598009700 Kenmore Range - Instructions

I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.

First I unpluged the range from the power source. Then I removed the back cover, disconnected the two wires to the element, remover two screws on the inside of the oven the held the element in place and removed it. I then installed the new element in the reverse order. This took about one day to get the new part and 15 to 20 mins to do the repairs. I figured that I saved at least $55 on a repairman service call.

remove two screws, remove two slide on wire connections and remove element. reverse to install.

I removed the two screws, puled out the element and took the pliers to unhook the two wires.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

After the repair I determined that the door did not need to be removed from the stove. The top 3 screws needed to be taken out, the front clase needed to be slid out by pushing it right to left or left to right. Then the bracket that held the inside screw assembly needed to be removed. The new handle needed to be installed and the bracets put back into place. The front glass needed to be reinstalled right to left or left to right. The hardest part of my install was putting door back on the range, the hinges kept popping out of place before setting into the range. The best way to replace the hangle would be to not remove the door from the range.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Turned off circuit breaker. Unscrewed old element holders from inside broiler - 4 screws. Pulled old element out to expose slip on wire connection at end. R&R with the new one. Screwed assembly back in. Turned on CB and tested. Good to go.

replacing this was very easy and simple. I removed the 2 screws holding the support bracket then the 2 screws in back of the elemant ,pull clips off the element then installed it back like it was .....very simple...

Watched a utube video on replacing element on my model range. Found my Phillips screwdriver. An electric drill would have been a bonus but not necessary. Pulled out range, pulled out plug, removed 1 screw from the lower back cover, disconnected the 2 wires, went to the front and removed oven door and racks, unscrewed 2 screws holding the element. Put new element in and reverse dprocess. Test oven. It worked!!