79090921402 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from Sidney, NY
- Parts Used:
- 318372211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element didn't work
I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from ADAMSVILLE, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Weld Was Broken On Support Bracket On Element
Replaced element no problem?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Kettlersville, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner burned out
unplugged old burner plugged new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greencastle, PA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" left front surface element would no longer heat properly
I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Wimauma, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Purchased home where previous owner melted Aluminum Foil to bottom panel of oven.
Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from Summerton, SC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element not heating right
Took old one out and plugged the new one into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Williamsville, VT
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace terminal block and burner unit.
Very simply following the online video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donnie from McLaughlin, SD
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven was too hot code f-10 came up
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Mansfield, MA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Logansport, IN
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
I had placed aluminum foil on bottom and it adhered to the surface.
I removed two screws and lifted out the ruined bottom. I set the new bottom in, but could not get the screws lined up so left them out. The bottom is heavy enough, it is not going anywhere. I am very grateful the part was available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentina from Riverside, CA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Three terminal blocks burned out (disintegrated) on electric stove
First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from Pensacola, FL
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No current to the burner
Checked the burner and no power to heat the burner. removed the old switch and put on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vince from west bloomfield, MI
- Parts Used:
- 316437703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke hinge point
Simple just remember there is a hinge lock on the hinge just open the door reach down to hinge and lift lock it blends in but its there close the door and pull out the door pull 2 screws on the hinge connecting it to door install new hinge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from big pine key, FL
- Parts Used:
- 316203200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
broil element burn out
take back planel off, take wires off old element and intsall new element hookup wires, put back planel ..under one hour job
Was this instruction helpful to you?
Thank you for voting!