7909621440A Kenmore Range - Instructions

Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.

Replaced control units that were malfunctioning.

Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!

Unplug the range, pull the knob off the front. Remove the screws from the cover plate behind the switch and remove the cover plate. Carefully pull one wire at a time off of the old switch noting the markings: "L1," "L2," "H1," etc., as the wire position may be different on the new switch. Put each wire onto the new switch as they are removed from the old one. Let the new switch hang from the wires while removing the 2 Phillips head screws from the front of the old switch and remove the switch. Hold the new one in place, start both screws, & then tighten them. Push the knob on the new switch. Plug the range in and try it. If everything works, install the rear panel and screws. I think that it took me longer to type this than it did to actually do the job.

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.