Models > 79095032501 > Instructions

79095032501 Kenmore Range - Instructions

Jump to:

All Instructions for the 79095032501

Customer:: daniel from fargo, ND
Parts Used:: 316468600
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

Replacing the Oven Door Vent Trim

1. Remove the old Trim by opening the door and unscrewing the two top screws holding the trim and glass to the door. 2. Lift the trim piece off of the glass, being careful as the glass will be a bit loose, and unscrew the handle from the trim piece, discard those two screws. 3. Place the new trim piece on the glass so that it fits snugly. 4. Place the screws back through the holes on the inside of the door, through the new trim piece and attach them to the handle. 5. Tighten down snugly and close door. You are done!

Was this instruction helpful to you?

Customer:: Ralph from Peoria, IL
Parts Used:: 316436001
Difficulty Level:: A Bit Difficult
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Infiniti switch needed to be changed.

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

Was this instruction helpful to you?

Customer:: Benjamin from Savoy, IL
Parts Used:: 316468600
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

self clean process changes the color of the trim

I checked the internet and found PartSelect.com the most affordable (lowest price) for the part. I got the part within 3 days which was very quick. Replacing was unscrew and re-screw at two points. it took me about 15 minutes (including opening the box and talking to my wife on the phone for 5 minutes).

Was this instruction helpful to you?

Customer:: James from Greenville, TX
Parts Used:: 316239700
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Gasket In Door Replaced

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Was this instruction helpful to you?

Customer:: ALBERT from LITCHFIELD, CT
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

bad burner switch

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

Was this instruction helpful to you?

Customer:: John from Columbiana, OH
Parts Used:: 316233903
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Temp did not match readout.

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

Was this instruction helpful to you?

Customer:: Eric from Mosier, OR
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

front left burner was on HI no matter what the dail setting was

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

Was this instruction helpful to you?

Customer:: Diane from Natrona Heights, PA
Parts Used:: 316239700
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

55 yr old wall oven had burnt out seal

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

Was this instruction helpful to you?

Customer:: Susan from Hillsboro, OR
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Switch was Sparking

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

Was this instruction helpful to you?

Customer:: Kelly from Marietta, GA
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Largest burner was not operational

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Was this instruction helpful to you?

Customer:: Justin from Madison, AL
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Hot Surface Light won't turn off.

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

Was this instruction helpful to you?

Customer:: Marshall from Newport,, NC
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Switch was sparking

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Was this instruction helpful to you?

Customer:: Smtella from Wappapello, MO
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

My burner would stay on high regardless of where it was set.

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

Was this instruction helpful to you?

Customer:: JILL from VIRDEN, IL
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Large Burner On Glass Top Quit Working

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

Was this instruction helpful to you?

Customer:: ruben from moss point, MS
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers, Socket set

range top left big burner would not come on.

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

Was this instruction helpful to you?

All Instructions for the 79095032501