79096524401 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from TULSA, OK
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element fried, found nothing in town, Part Select delivered in three days
Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.
Gary H.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BENTON, IL
- Parts Used:
- 316238201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The range element was not coming on
After settling that it was the Surface Element Switch, ordering and securing the switch, the first step was to disconnect the power to the Oven/Range. Next pull out the Range and remove the back and disconnect the switch from the top of the Range. Using the new switch I removed the wire connectors from the old switch and reconnected them to the new switch in the same spot that they came from. After connections were secure I reattached the switch to the back of the Range and reattached the back of the Range. When everything was back in place the power source was reconnected and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from APACHE JCT, AZ
- Parts Used:
- 316282100
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
There was no instructions. The wires don't match up old vs new. I read the reviews and this helped.
However the 1a 1b etc. Are very hard to see thus the need to magnify. Then it was easy.
I must say the guy I talked to was very nice.
I must say the guy I talked to was very nice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from New Haven, CT
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
. F3 error code
I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Colchester, CT
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element would not heat up
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from PACHECO, CA
- Parts Used:
- 316404002
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
wrong part received and returned
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patti from Greer, SC
- Parts Used:
- 5304503232
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked inside glass
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abe from Manson, WA
- Parts Used:
- 5304528972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner quit working
Received the new part FAST. Ordered online. Easy to plug in the new part. Will use PartSelect.com again when needed to order parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brant from Saint Paul, KS
- Parts Used:
- 5304445529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Change Out oven Door Hinges
I first found a video on Youtube and watched it. Then you flip the hinge latch up and remove door from oven. Then remove 2 door handle screws and 4 screws from the bottom of the door. Then remove 2 screws from each existing hinge. Place new hinges on with new screws that came with the kit. Then replace the 4 screws on bottom of door and then the 2 handle screw and place door back on the oven and open door about half way open then flip hinge keepers back up close door and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!