79094049700 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ALBERT from BENTONVILLE, AR
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner would no turn off.
A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Acton, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner would stay on and the hi-temp safety limit switch is all that would shut it off.
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Kingsport, TN
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Large element would only heat on high.
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.
Was this instruction helpful to you?
Thank you for voting!
Large burner wouldn'cycle to temperature setting
Large burner would cycle on and off per temp setting a few times. Then it would stick on high. Read other problems people had with the burner switch, which helped to determine the problem. Instillation per video was pretty straight forward; but the issue I ran into was when pulling off the wires from old switch, there was a short wire which connected to the indicator light. The abrupt release yanked the wire which caused the lens indicator to snap. So, when you are repairing the switch, be aware if there is enough slack in the wires to prevent that issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from Huntington Station, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replaced large burner switch on tappan range
I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma J from Riverview, FL
- Parts Used:
- 5304503232
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
inner glass door was broken
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
Was this instruction helpful to you?
Thank you for voting!