7909421940A Kenmore Range - Instructions

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Just followed the instructions

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.

Removed two screws removed and replaced panel.

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.

Removed the old & simply inserted the new one

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.