79090821408 Kenmore Range - Instructions

At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief:
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.

I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.

Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Ordered new racks and replaced them.

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

I first unplugged the stove (which was the hardest part), I then set a bright light so I could see near the back of the oven. I then started the task of removing the old element by using a quarter inch nut driver, not to difficult at all. Once I removed the bracket I pulled it out far enough so I could disconnect the wires that were connected to the element. I had a bit of a hard time with one but after a little wiggling I got it loose. I was then able to remove the old element from the oven. I began the replacement of the new one, EASY ! I placed it in the oven, attached the electrical connection to the new element (made sure they snap in tight) and then replaced the bracket that held the element /coil to the back of the oven using the nut driver. All finished in about 15-20 minutes. I am not a strong woman , but a determined one. This fixed the problem and I am now baking like I have a new stove. The surface element is nothing to change , just unplug the old one and plug in the new one (simple). I use my front burner so much that it had began to smoke from so much food dropping and cleaning it over the years. MY main issue was the Bake Element and I really like my range and thought I would try this before buying a new range and I did it myself ! If I can do this anyone can believe me I am NO repair person, but this was very easy to do.

LOOKED FOR MODEL# OF STOVE.. ENTERED MODEL # IN PARTS.COM SEARCH.
MATCHED COIL AND DRIP PANS
ITEM NUMBERS AND SIZE.
PLACED ORDER.
ARRIVED FOLLOWING WEEK WELL PACKED.
PULLED OUT OLD COILS/DRIP PANS.
PLACE *NEW* DRIP PANS IN FIRST. THEN PUSH IN *NEW* COILS
**NO PAID INVOICE WAS RECEIVED**
Wed4/24/2024

Make sure whichever surface element you are to replace is OFF.Carefully remove surface element by pulling it out of socket and remove drip bowl. Cleaned area around range top and place new or old drip bowl in place. Line up drip bowl cutouts and place on range top and simply push in/plug (2 prongs)in new surface element and place on drip bowl. It's that easy! To install 2 new surface elements and drip bowls took less than 5 minutes.

Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.