79094333704 Kenmore Range - Instructions

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Large burner would cycle on and off per temp setting a few times. Then it would stick on high. Read other problems people had with the burner switch, which helped to determine the problem. Instillation per video was pretty straight forward; but the issue I ran into was when pulling off the wires from old switch, there was a short wire which connected to the indicator light. The abrupt release yanked the wire which caused the lens indicator to snap. So, when you are repairing the switch, be aware if there is enough slack in the wires to prevent that issue

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Removed outer glass first ,then worked my way thru to inner glass..