79096533500 Kenmore Range - Instructions

If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damaged screw and then installed the replacement. Wish all appliance repairs were this easy!

Easy as 1-2-3

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.