79036723603 Kenmore Range - Instructions

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

Unsrewed side plates and removed old hinge and replaced with new. Recomend doing both left and right hinges or door will not close square.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

A friend replaced the new ignitor with the old one...very simple job.

I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.

The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

First I'll say the instructions and comments from this site were right on, making it easy. I slid the oven out and unplugged the electric. Opened the door, took out the racks, took out the two thumbscrews at the back bottom and lifted the bottom plate up and out, and lifted off the heat guard plate. I could then see and reach the igniter pretty easily (the flashlight helped). The igniter may have been replaced before because there were already wire nuts on the wires. I unscrewed the two screws using the nutdriver and noted which wire (top or bottom) went to which wire inside. Unscrewed the wire nuts and removed the old igniter. Used the old igniter to determine where to cut and strip the new igniter's wires. Connected the wires of the new igniter using the wire nuts and put the two mounting screws in. Then just put all the other stuff back in (heat guard, bottom plate/two thumbscrews, racks). Plugged it in and started the oven. Got a small amount of "crackly" noise initially (maybe because the igniter was new) but that went away and it's been working fine and quiet since. Very easy (well, perhaps other than being on your knees, leaned into the back of an oven for a couple minutes). Well worth the effort.

Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.

1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks

suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.

After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igniter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.