79095042503 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sean from ASTORIA, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Electric element would intermitantly go on high, even on low settings.
Slid stove out, disconnect power plug, removed top control panel with 4 screws. Unplugged two electrical connectors. removed knob and nut removing switch. Re-assembled in reverse order and test all functions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from LEWES, DE
- Parts Used:
- 316278800, 5304409888
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Old terminal block was melted
removed back panel on range, removed old terminal block installed new terminal block, replaced back panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Colchester, CT
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element would not heat up
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Hauppauge, NY
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
over draw was off track
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Florence, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from morton, PA
- Parts Used:
- 316468600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cracked range oven door handle
removed 2 screws from inside oven door swap out old to new handle reinstall 2 screws done less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miriam from BROOKLYN, NY
- Parts Used:
- 316278700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screws were damaged
Took out old screws and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEWISTON, ME
- Parts Used:
- 316225001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken element
I followed instructions on your video. Took 10 minutes. My wife thought I was a pro.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from MONTANA CITY, MT
- Parts Used:
- 3051162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
guide was broken
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from W SAND LAKE, NY
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8" burners were not responding correctly to the switches
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from UNIONTOWN, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Switch quit working and wouldn't turn
Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from KERSEY, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
sparking element
removed back and transferred four wires to new part and replaced back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- errol from bronx, NY
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear Drawer Glide
Just use flat screwdriver to press on clip and just squeeze it in
Was this instruction helpful to you?
Thank you for voting!