Models > 79090939600 > Instructions

79090939600 Kenmore Range - Instructions

Jump to:

All Instructions for the 79090939600
106 - 120 of 636
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Sherry from JAMES STORE, VA
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from KLAMATH FALLS, OR
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Bake element burnt in half
All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RAYMOND from JONESBOROUGH, TN
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from GERMANTOWN, NY
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Bake element broken
Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jean from MARIETTA, GA
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marion from NEWPORT, TN
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from ALBANY, OR
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Socket set
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Josh from SAINT PAUL, NE
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Element burned out in the house we rent
Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from ROCKVILLE, MD
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Broken element
Simple installation took 2 minutes to do...pop on the connectors, screw each end into back of oven...DONE.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
carol from LAUREL, MD
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donise from WILLINGBORO, NJ
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The bake element had burned out.
I followed the instruction on the web site and the installation was just like the instruction. Very quick and easy. I was so happy and now I am baking up a storm again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lee from LEES SUMMIT, MO
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Defective element
Very easy. Remove two screws, pull element forward, remove two wires, install wires on new element, push backward and reinstall the screws. Done!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from New Castle, PA
Parts Used:
318372211
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from NEWCOMERSTOWN, OH
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Bottom element burnt out. Bad design on this element.
Turn power off. At oven, removed two screws from element hanger. Pulled old element out exposing spade connectors. Pulled connectors lnstalled connectors on new element and shoved back in stove and replaced screws. Work done with oven door open using drop light. Check for debris, turn power on, turn oven on to check.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from wilmington, DE
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Fried baking element
Unplugged stove, removed screws holding element In place. Pulled element forward exposing electrical ends. Removed connectors, re- connected ends to new element. Pushed element back into holes and reconnected the screws. Plug stove back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79090939600
106 - 120 of 636